Anyone know a crossover for the rear bushings ?

[2015 Z Force 800 53/Trail EPS]

There are none as far as I know. OE is all we have for now.

That's just Great 👎

I found aftermarket front ones at a dealer here I just didn't want to do the drive but I guess I'll be calling them in the morning lol 🤞

[2015 Z Force 800 53/Trail EPS]

That's just Great 👎

I found aftermarket front ones at a dealer here I just didn't want to do the drive but I guess I'll be calling them in the morning lol 🤞

Who makes aftermarket fronts?

For the old 800s they were close to the old Polaris RzR 800 and with a little modification they could be made to work all around. But not sure of the new 1000s.

For a while Garage Products made a great set for the Zs but as far as I know they quit. I had some rear knuckle bushings failing because of the spacers and went with OE just because I didn't want to modify and knurl another set of RzR bushings. Can't believe I paid that much for Chinese bushings and sleeves.   

That's just Great 👎

I found aftermarket front ones at a dealer here I just didn't want to do the drive but I guess I'll be calling them in the morning lol 🤞

Who makes aftermarket fronts?

For the old 800s they were close to the old Polaris RzR 800 and with a little modification they could be made to work all around. But not sure of the new 1000s.

For a while Garage Products made a great set for the Zs but as far as I know they quit. I had some rear knuckle bushings failing because of the spacers and went with OE just because I didn't want to modify and knurl another set of RzR bushings. Can't believe I paid that much for Chinese bushings and sleeves.

There not a perfect match but

The dealer gave be a set of allballs
Bushings for the front said that's what they use on all of them just add a 9/16 washer between the bushing an ear as the head isn't quite as thick they been doing it for yrs I guess
I never put them in yet as they just had a loose nut lol but I need to do my backs for sure there pretty sloppy

I'll post both when I talk to them if they have a rear option

Soooo here's what my local dealer uses an sells

It's allballs kits
Now to work they require a washer behind each bushing no big deal imo

Fronts 2 box's an 8 washers

An the rears are 20washers an see pic

So far fit like a glove the washers are a must just takes up that lil bit of a difference an the ears fit snug on each side

Lil update final did the rears All but one upper inner arm

The new ones fit tight in the arms sleeve was tight sliding in
The washers are just barley thin enough an fit perfectly I'll update when they wear out lol I'm about 3300kms now

[2015 Z Force 800 53/Trail EPS]

Nice. When I use the Polaris bushings I use these nylon washers. They have a 5/8" center that slips over the sleeve and have to be adjusted on thickness a hair to slip in. Still..pretty cheap and don't wear on the mount brackets like the steel washers I had before did.

Got mine off ebay cheap a couple of years ago but all I can find now is these from Amazon. Still..not bad 50 for under 11 bucks.

https://www.amazon.com/Washer-Finish-Off-White-Nominal-Thickness/dp/B009OLR92S/ref=sr_1_2?crid=2KPH8GIB51Q4Z&keywords=5%2F8%22%2BID%2BNylon%2Bwashers&qid=1671229023&sprefix=5%2F8%2Bid%2Bnylon%2Bwashers%2Caps%2C144&sr=8-2&th=1

Ya that would be the ticket for sure
I'll be doing that on the next swap