noise when starting

NL800 · February 06, 2019, 10:51:59 PM

Perfect. Was it much of an issue to install.

Dave K · February 13, 2019, 07:07:48 PM

Mine was under warrenty.

maxim552 · March 19, 2019, 05:46:25 PM

dealer wants $300 plus tax for overriding clutch found these online, anyone every order here.

http://online.mortch.com/MICF800-6015-CFMoto-CF800cc-ATV-UTV-Overriding-Clutch-0180-091200-CF2V91W

http://online.mortch.com/MICF800-6015A-CFMoto-CF800cc-ATV-UTV-Driven-Gear-0800-0900A1-2V91-Starting-Clutch

anyone know anyway to tell which one i need , teeth or no teeth with out pulling the side cover off? also do i need to drain the oil for this. tia

NMKawierider · March 19, 2019, 06:32:14 PM

Quote from: maxim552 on March 19, 2019, 05:46:25 PM
dealer wants $300 plus tax for overriding clutch found these online, anyone every order here.

http://online.mortch.com/MICF800-6015-CFMoto-CF800cc-ATV-UTV-Overriding-Clutch-0180-091200-CF2V91W

http://online.mortch.com/MICF800-6015A-CFMoto-CF800cc-ATV-UTV-Driven-Gear-0800-0900A1-2V91-Starting-Clutch

anyone know anyway to tell which one i need , teeth or no teeth with out pulling the side cover off? also do i need to drain the oil for this. tia

Look it up on Alpha-Sports.com first, then order it from the cheapest place as both use CF Moto parts. And yes, because you will be pulling that case side cover you will need to drop the oil.

maxim552 · November 05, 2019, 11:15:30 PM

changed out the starter clutch/ spragg, still getting same noise. new starter ordered.

doug80638 · November 06, 2019, 07:27:19 AM

Did the original spragg look undamaged? The shaft unmarred?

Have you used a mechanics stethoscope to narrow down the source of the noise? That would tell you instantly if it was the starter.

Did you run it with the cover off? If so, same noise?

November 06, 2019, 09:35:29 AM

I found the starter motor bushing dry on a 500hoe, probably same starter motor.......easy to take apart.

maxim552 · June 04, 2020, 10:47:45 PM

replaced the spragg clutch before winter and was still getting same noise. replace starter today and fired right up, no noise at all. hope stays this way lol

June 05, 2020, 07:12:19 AM

See post #21, I have a few of these & the fix is simple. The starter comes apart easily & goes back together the same. Each time there has not been grease in the end cap bushing.

The noise is horrible in the worst case as in yours.

maxim552 · June 10, 2020, 02:21:53 AM

Quote from: ctdls on June 05, 2020, 07:12:19 AM
See post #21, I have a few of these & the fix is simple. The starter comes apart easily & goes back together the same. Each time there has not been grease in the end cap bushing.

The noise is horrible in the worst case as in yours.

do you have any videos of this. when i took they old starter off and connect to a jumper box it spin freely, i guess no load on it. still have it and would like to try the regrease and keep it.

maxim552 · June 10, 2020, 02:25:56 AM

Quote from: doug80638 on November 06, 2019, 07:27:19 AM

Did the original spragg look undamaged? The shaft unmarred?

Have you used a mechanics stethoscope to narrow down the source of the noise? That would tell you instantly if it was the starter.

Did you run it with the cover off? If so, same noise?

shaft was unmarred, not a mark on it. the original spragg look ok except there was a small crack in it so glad i did change it.