gear(or anything else) slip during drive

Started by thewind60, March 20, 2016, 08:09:40 AM

0 Members and 5 Guests are viewing this topic.

Previous topic - Next topic

thewind60

Guest
Logged
thewind60
Guest
hello
i have faced twice the scenario that i am driving my zforce and suddenly the gear like moving to neutral and getting back to drive...
i am not sure what can cause this issue is the Belt can do it? is it the clutch?
please tell me what you think or if anyone faced it before...
thx

NMKawierider

Global Moderator
*****
Guru
Posts: 12,593
2015 ZForce 800 53 (Trail)
Logged
NMKawierider
Global ModeratorGuruPosts: 12,593
Quote from: thewind60 on March 20, 2016, 08:09:40 AM
hello
i have faced twice the scenario that i am driving my zforce and suddenly the gear like moving to neutral and getting back to drive...
i am not sure what can cause this issue is the Belt can do it? is it the clutch?
please tell me what you think or if anyone faced it before...
thx

Check the engine mounts. If they can move it can pop out of gear. Other then that check the detent alignment. It may need adjusting.
2015 Z Force 800 53/Trail EPS
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage |7- 9.7" GPS Systems | Bandit Springs Rear & Gen-3 Shocks Front | Cage Chop Mod

My Videos On YouTube

thewind60

Guest
Logged
thewind60
Guest
#2
thx alot for your inputs...
what is detent mean ?
did it happens to you?


NMKawierider

Global Moderator
*****
Guru
Posts: 12,593
2015 ZForce 800 53 (Trail)
Logged
NMKawierider
Global ModeratorGuruPosts: 12,593
Quote from: thewind60 on March 20, 2016, 03:10:27 PM
thx alot for your inputs...
what is detent mean ?
did it happens to you?

Detents are the "clicks" in the transmission where it locks into each gear selection. The gear shifter also has detents or notches where each gear is. Both have to line up. You do this with the gear shift rod that goes between the shifter and the transmission.

This did happen to me where under load it would sometimes kick from H to half way to N which would take it out of gear. It also had a hard time going into low and reverse.
2015 Z Force 800 53/Trail EPS
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage |7- 9.7" GPS Systems | Bandit Springs Rear & Gen-3 Shocks Front | Cage Chop Mod

My Videos On YouTube

Spaceman78

Guest
Logged
Spaceman78
Guest
Also could be belt slipping.

gfmoto

Supporting Member
****
Guru
Posts: 1,185
Let's ride!
Logged
gfmoto
Supporting MemberGuruPosts: 1,185
Had my dealer adjust the linkage and it works great now. Worked ok before not popping out of gear just a few times not going into L properly.
2015 ZForce 800EX
32" light bar
2-4" spots
Custom Cv guards
DIY 1/2 windshield
UNI air filter
DIY rear window
BOSS ATV 28. 450W speakers
Alpena Rock Lights (tough pods)
2" RZR Bracket lift
Roof extensions
27" Maxxis Corranado Tires
Alpena RGB rock lights
SuperATV Rocksliders
1/2 Doors w/custom paint and graphics