I purchased the replacement headlights, taillights, handlebar switch, and flasher from my local dealer.  You can check with a local dealer or they also sell them through the https://cfmotousaparts.com/ website.

My lights did not include the turn signals.  If you look close at the headlights, if they have the turn signals your should see a strip of LED lights maybe 4 or 5 on the center top portion of the headlight.  Check your tail lights, the round light on the outside edge is the portion that will be your amber blinkers.  So if you hit your brakes and these round areas light up as red brake lights, I assume you will need to replace them.  If you look them up on the cfmoto parts site, it should show them. If you do need to replace them, they are reconfigured as plug and play, you do not have to splice any wires.

As for the indicators in the dash, yes mine did and from what i was told these are pre-installed.   If you do install the turn signal items, nothing will work until you plugin the flasher.   After that you will have blinkers and additionally there is also 4-way flashers.  All are controlled by the replacement switch that you install by replacing your current left hand side switch controller.

Have a great day and good luck.

Yes I installed the new factory switch setup.  It actually is nice, even includes a flasher button.  The dash indicators works with this setup.  All is plug and play.  Good luck!

2022 Cforce 800 XC
After Contacting CFMoto USA, CFMoto CA, CFMoto Parts, and Local Dealer, with no information of the location of the plug to connected the factory wiring to the turn signal flasher.  I have to give props to the local dealer as they looked at all of their information, contacted both USA and CA offices with no information given. I have spent hours on the internet looking for posts on this subject and only found people saying they don't know or there is no such plug on these units. 

To start with, i don't understand why this information isn't widely given out.  I understand that in a lot of states ATVs can not be legally driven on roads, but the factory has installed the factory ready turn signal wiring.

A little background.  I rather purchase the factory turn signal upgraded tail lights, head lights, handle bar switch, and flasher.  I like the nice look and operation of the factory items, instead of adding an aftermarket turn signal kit.

I DID NOT want others to go through all the work I went through to find this plug, so i plan to contact my local dealer and post on the internet anywhere i can to spread the word.  I spent hours and tore my brand new machine down.  I removed anything that was covering the wiring on this machine.  I traced the wiring from each tail light, head light, and controller.

The flasher wire/plug is located in the center of the machine, up high about halfway between the hand bars and the battery.  To get to the plug remove the underside black plastic wheel wells on the passenger/right side front wheel.  There are two parts, better to remove both.  The front piece has to be removed anyway to install the right headlight.  You will need either a clip removal tool or a couple of screwdrivers to remove a number of clips.  Also a Philips screwdriver to remove two screws and a 10mm ratchet for one screw on the front side piece.  The plug is located on a small wire loom with three wires and a dummy cap that will need to be removed and then you will be able to insert the factory flasher.

A little more location description:  Located above the top bar, about 2 to 3 inches towards the back of the machine from the right front shock.  So slightly above the shock and towards the back of the machine.  There will be a number of plugs and wire looms in this area.  Gently pull on the smaller wire looms (about 1/4 to 5/16" in diameter).  The wire loom is zipped tied with one tie to the frame with about 3 inches of wire hanging with the plug.  Plug is black in color.

I know this was a lengthy description, but i don't believe this information is anywhere!  So just trying to help out others!  I will attach a few pictures to hopefully also help out.  Let me know if you need further assistance.