I used 3.4 for the rear and 4.4 amber for the front.

https://www.amazon.com/gp/product/B09289FX68/ref=ppx_yo_dt_b_asin_image_o05_s00?ie=UTF8&th=1

sorry didn't copy as a link

In looking at the pictures for the gaming rack, the lower mounting brackets do not exists on the 1000XL unless that's an aftermarket bracket.

You guys (& gals) come up with some of the neatest stuff for our rides. Love it.

One question, will this work with the CF Moto half doors that use the same attachment points on the 1000XL?

I ended up getting the one made by Rival and it fit with my CF Moto with half doors. I did have to add spacers for the mirrors on both sides but it worked out great. I bought mine for under $350, but now I see there up to $479.

Not being a smart ass, I know when I installed my 2023 switches for the turn and hazards, I matched the pigtail tag Chinese characters with those on the packaging of the switches to make sure I got the right plugs to the right switches. All worked well even though I didn't have the turn signal lights installed yet.

I have a uforce 1000XL, I left the back up lights connected as set up by the factory, I tapped into the other but connectors to after market turn signals. Just had to find a ground wire to tie into to complete the turn signal install.

Will this also fit the 1000XL?

Mine does, I'm still in the "break-in" phase. Time will tell if it goes away.

I have the half doors too, but if they made a enclosures to work with the half doors... I'd be interested in it. Best of both worlds.

However, it would be nice if someone could identify type and source where one could buy the connectors and pins that are used by CFMoto so they could build their own wire harnesses for aftermarket accessory installs.

The closest I found was on Amazon, a 6 pin connector with the male and female blade pins.

https://www.amazon.com/dp/B01DIHEO94?psc=1&ref=ppx_yo2ov_dt_b_product_details#:~:text=to%20zoom%20in-,uxcell%206%20Pin%20Waterproof%20Wire%20Connector%20Car%20Sealed%20Electrical%20Set%202.2mm,-Visit%20the%20uxcell

They matched exactly the 6 pin/spade connector that I used for my uforce 1000xl for the turn signals, not sure if they are the same for the flasher.

I have a 2023 UFORCE 1000XL.  Do the new machines come with the lights for turn signals installed in the headlight?  I know you have to install a switch and flasher but I thought the actual lights came in the headlamp

My 2023 UFORCE 1000XL does not come with turn signals in the headlamps or tail lamps. After installing switches and flasher That confirmed it. So I added some aftermarket type LED lights to fit my taste. Quite pleased with the results, I tapped into the front pigtails from the lamp side for the turn signals, and for the rear I tapped into the butt connector for the turn signals by the lamps. Not the simplest approach, but I have the time to tinker.

I tapped into the Orange (Drivers side) and Baby Blue (Passenger side) wires right at the connector under the bed.  I ran new wires to my 3/4" Side Marker lights I bought off Amazon and brackets off eBay.  I could have cut out the holes in the box under the taillights but decided against that.  I know some folks have tapped into the backup lights to use as signals but where I live and I'm sure it's across the country, turn signals should be Amber or Red.

Like this???

After watching various videos on ways to add aftermarket turn signal lights, here's my approach. I used all CFMoto switches and flasher unit. LED lights purchased through Amazon.com along with metri-pack type plugs. I tapped into existing wiring points for the rear turn signals by the rear light "jumpers", and for the front, I tapped into the plug going to the front lights with matching metri-pack crip blades.
Not the easiest and quickest approach but I didn't have to drill into the body.

I purchased an anchor for CFMoto and made my own bracket to hold the SMV sign.