0 Members and 1 Guest are viewing this topic.

*

Offline MarianT

One way bearing (800 ex)
« on: October 09, 2015, 07:43:40 PM »
Well, as I had told you the problem I had in the clutch, my dealer authorized me to disarm. When removing the cover, the one way bearing fell off, so i dont know if it was in the correct position, looking closely it i can see some roller marked, cant see another problem, the clutch was perfect, and the clutch housing too, and bearing in the case cover. i will post a picture
The question is how it goes, it has a few inscriptions and an arrow showing a direction, backside, nothing.
I think the engine turns to the tail of the utv, so the arrow must be in that direction, facing to me, the side that has nothing, is this correct?
One more thing, i couldnt open the secondary, i srcrewed a 6mm bolt but he opens a little and nothing, then i screwed up the thread, i think i have yo make a new one.

*

Offline MarianT

Re: One way bearing (800 ex)
« Reply #1 on: October 09, 2015, 07:52:33 PM »

*

Offline Cosmosdan

Re: One way bearing (800 ex)
« Reply #2 on: October 09, 2015, 08:22:17 PM »
There should be two tapped holes in the secondary. It might be binding when you are trying to open it up. Might be the end of the screw is too ruff, digging into the other side or too short of thread on the screw. Might also be at the helix. Try tapping lightly on the back pulley. Did you strip the clutch holes? If you did than there is metal inserts you can install.
2013 Z6 Trail
Iron Baltic skid plates
UE Boom Speaker mount
RZR 800 Shocks
Mostly stock trail riding
25g. Rollers and A1

2016 Outlander max 570
Too new for mods yet

*

Offline MarianT

Re: One way bearing (800 ex)
« Reply #3 on: October 09, 2015, 08:34:12 PM »
Thanks!, only one of the two holes has thread.
And another thing, i have to find the correct position of the one way bearing.

*

Offline NMKawierider

Re: One way bearing (800 ex)
« Reply #4 on: October 09, 2015, 09:02:32 PM »
Only one of my holes is threaded too. Also, the two cover bolts that are at the dow pins are longer then the rest and will open the clutch farther. I guess if the threads are stripped it's a mute point now but maybe you can tap the other hole.
2015 Z Force 800 53/Trail EPS
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage |7- 9.7" GPS Systems | Bandit Springs Rear & Gen-3 Shocks Front | Cage Chop Mod

My Videos On YouTube

*

Offline MarianT

Re: One way bearing (800 ex)
« Reply #5 on: October 09, 2015, 09:34:39 PM »
Kawie, can you help me with the one way bearing?, i have a new one, but dont whant to destroy him.

*

emersonsc

Re: One way bearing (800 ex)
« Reply #6 on: October 09, 2015, 09:41:27 PM »
Kawie, can you help me with the one way bearing?, i have a new one, but dont whant to destroy him.

The one way bearing should have writing on one side. The writing faces the inside toward the cylinder.

*

Offline MarianT

Re: One way bearing (800 ex)
« Reply #7 on: October 09, 2015, 09:58:42 PM »
Thanks a lot. i think it was backwards and hurted the wet clutc too.








share image


*

Offline NMKawierider

Re: One way bearing (800 ex)
« Reply #8 on: October 09, 2015, 10:32:50 PM »
Sorry, I have not yet had mine apart. emersonsc has though. I do know that when I was tightening the nut on the primary it would tighten against the one way.
2015 Z Force 800 53/Trail EPS
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage |7- 9.7" GPS Systems | Bandit Springs Rear & Gen-3 Shocks Front | Cage Chop Mod

My Videos On YouTube

*

Offline MarianT

Re: One way bearing (800 ex)
« Reply #9 on: October 09, 2015, 10:46:05 PM »
To extract the belt is a 6 mm screw on the secondary?

*

Offline Cosmosdan

Re: One way bearing (800 ex)
« Reply #10 on: October 09, 2015, 11:28:34 PM »
Correct it is M6 x 1.0  Just check the hole size with a drill bit before trying to tap it. Too small and it won't go well. here is a link about the inserts I was talking about. They work well. I use high strength loc-tite when I put them in. You can find them a lot cheaper if you look around.

http://www.grainger.com/product/E-Z-LOK-Thread-Insert-4ZE49?s_pp=false&picUrl=//static.grainger.com/rp/s/is/image/Grainger/4ZY16_AS01?$smthumb$
« Last Edit: October 10, 2015, 01:39:00 AM by Cosmosdan »
2013 Z6 Trail
Iron Baltic skid plates
UE Boom Speaker mount
RZR 800 Shocks
Mostly stock trail riding
25g. Rollers and A1

2016 Outlander max 570
Too new for mods yet