[Danielshepard86]

Does anyone know the specs of the stock 14" wheels of a 2015 ZForce 800ex? Looking for the offset in mm (wether is + or -) and the numbers like "5+2" or "5+3" etc of the oem wheels. I am looking to add aftermarket 14x7" wheels to my rig that will give me a bit wider of a stance over the stock wheels.  Thanks in advance!

[NMKawierider]

They are real close a 2" outset. When I put my 5+3s on it only added just under 2" to the front. I posted this on the FB page.

[Danielshepard86]

I am having problems finding 5+3 for a reasonable price. I did, however, find a set that is listed as a +10 offset. This is where I would need to know the oem offset to see if a +10 would give a wider stance

[NMKawierider]

I am having problems finding 5+3 for a reasonable price. I did, however, find a set that is listed as a +10 offset. This is where I would need to know the oem offset to see if a +10 would give a wider stance

You can use this converter. It will show the amount of inset. The rest is the outset. For example lets say you have a 7" wheel that is stamped +10. That shows an inset of 4.39. The rest of the 7" goes to the outside. Just round the results ...so that wheel would be a 4+3. You have to know the wheel width though and that is from the inside of the bead surfaces.

https://www.customwheeloffset.com/tire-wheel-backspacing-offset-calculators

[Danielshepard86]

The exact specs for the wheels I am looking at are

14x7
+10et

According to that calculator and the above response, these will in fact give me a wider track. Am I following this correct?

[NMKawierider]

The exact specs for the wheels I am looking at are

14x7
+10et

According to that calculator and the above response, these will in fact give me a wider track. Am I following this correct?

Should be about 2" wider total....at least up front. I think the stock rears are wider then the fronts but I think...that also have the 2" outset.

[Spaceman78]

I don't know the off-set of the stock wheels. I put 14x7 on mine. They came off my Grizzly. I think they are 5+2, but not sure. They gave me about 2" width in front and 3" in the rear. I was going to put the stockers back on my grizzly when I traded it off, but the right rear tire would have been under the muffler, because of the narrow off-set.

[autorvshop]

I PUT DOUGLAS STEATH WHEELS ON MY Z800  8 IN ON THE FRT 10 IN ON THE REAR, LOOK THEM UP FOR A YAMAHA 1000 ON ROCKYMOUNT ATV  FRT ARE 4 X 4 OFF SEAT REAR ARE 5 X 5 OFF SET IT ALLOWED ME TO REMOVE MY WHEEL SPACERS, I ALSO RUN THE DOUGLAS MOAPA RUN FLAT TIRES  28/10 ON THE FRT 28 X 12 ON THE REAR , NO LONGER NEED TO CARRY A SPARE

[Danielshepard86]

I wanted to update this in case anyone is after the same information. Stamped on the rear of the factory Cfmoto wheels is their offset. The wheel specs for a 2015 cfmoto ZForce 800ex are as follows:

Front wheel: 14x7 +23 offset

Rear wheel: 14x8 +46.5 offset

So in my case, a set the set of 14x7 wheels with an offset of +10 would in fact, stick out another 1/2" (.512 to be exact) in the front and the rear would stick past 15/16 (.937) over the factory wheels. Thanks for the help, hope this helps! New wheels ordered, will post pics soon!