Author Topic: ZForce 800 Fan Switch Bypass  (Read 4114 times)

0 Members and 1 Guest are viewing this topic.

Offline NMKawierider

  • Global Moderator
  • Guru
  • *****
  • Posts: 5397
  • 2015 ZForce 800 EPS
    • View Profile
    • Visit my YouTube Channel
  • Location: Albuquerque, NM
Re: ZForce 800 Fan Switch Bypass
« Reply #15 on: August 14, 2018, 03:34:39 PM »
Just got the switch (same as shown). I need the wiring diagram.
Thanks.
Just follow the two wires from the thermoswitch which is the only thing on the radiator on the right side with wires going to it. All you are doing is making a manual connection between the two. I did it there mostly because it was easy to get to.
2015 Z Force 800 (53") EPS -
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор (Rodin's) Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage | Magellan TRX7 GPS| Bandit Springs

My Videos On YouTube

Offline Jaco499103

  • Junior Member
  • **
  • Posts: 5
    • View Profile
  • Location: Utah
Re: ZForce 800 Fan Switch Bypass
« Reply #16 on: August 17, 2018, 10:11:49 AM »
Thanks, I'm asking about the switch itself five connections on back and no instructions. By the way I did your first stage of the air intake it looks great and i'ts much easier to change of clean filter. 

Offline NMKawierider

  • Global Moderator
  • Guru
  • *****
  • Posts: 5397
  • 2015 ZForce 800 EPS
    • View Profile
    • Visit my YouTube Channel
  • Location: Albuquerque, NM
Re: ZForce 800 Fan Switch Bypass
« Reply #17 on: August 17, 2018, 10:59:53 AM »
Thanks, I'm asking about the switch itself five connections on back and no instructions. By the way I did your first stage of the air intake it looks great and i'ts much easier to change of clean filter. 
If you have just an ON-OFF switch with LEDs, then I think I have the switch wiring on the How To. If not, I think this is it. The first is the 4-connector.



Then the 5 connector.



Or better yet, this one but the color code is for the RPM limiter override I replaced my momentary switch with one that stays on. You will use the gray/black and the green/black and nothing else unless you want to tap-in to the dash LED 12V power and the ground. DO NOT use any power or ground  from the thermoswitch to light the switch or provide a ground for the switch's lighting:


« Last Edit: August 17, 2018, 11:06:18 AM by NMKawierider »
2015 Z Force 800 (53") EPS -
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор (Rodin's) Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage | Magellan TRX7 GPS| Bandit Springs

My Videos On YouTube

Offline Jaco499103

  • Junior Member
  • **
  • Posts: 5
    • View Profile
  • Location: Utah
Re: ZForce 800 Fan Switch Bypass
« Reply #18 on: August 18, 2018, 12:12:31 PM »
Thanks so much. I have the 5 pole switch, works perfect.