Author Topic: Rear control arm bushings  (Read 157 times)

0 Members and 1 Guest are viewing this topic.

Offline Twztd

  • Full Member
  • ***
  • Posts: 41
    • View Profile
  • Location: Pennsylvania
Rear control arm bushings
« on: September 22, 2018, 07:42:03 AM »
So I put my bracket lift on and noticed I have a lot of movement in the rear control arm bushings if I shake the rear tire from front to back. Does anybody have this same problem? I was going to order new bushings from Alpha, but they will probably do the same thing in a short time... Any suggestions?

Offline NMKawierider

  • Global Moderator
  • Guru
  • *****
  • Posts: 5399
  • 2015 ZForce 800 EPS
    • View Profile
    • Visit my YouTube Channel
  • Location: Albuquerque, NM
Re: Rear control arm bushings
« Reply #1 on: September 22, 2018, 09:01:03 AM »
I replaced all mine with ASR Delron bushings for the 800 RzR and custom fit nylon wear washers on all to end that issue with all the bushings. The vid is in the how-tos.
2015 Z Force 800 (53") EPS -
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор (Rodin's) Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage | Magellan TRX7 GPS| Bandit Springs

My Videos On YouTube

Offline Twztd

  • Full Member
  • ***
  • Posts: 41
    • View Profile
  • Location: Pennsylvania
Re: Rear control arm bushings
« Reply #2 on: September 22, 2018, 12:39:27 PM »
I replaced all mine with ASR Delron bushings for the 800 RzR and custom fit nylon wear washers on all to end that issue with all the bushings. The vid is in the how-tos.
Nice! I'll take a look see at your video then. Is there a site you used and roughly about how much did you pay for the kit? Thanks for the heads up!

Offline NMKawierider

  • Global Moderator
  • Guru
  • *****
  • Posts: 5399
  • 2015 ZForce 800 EPS
    • View Profile
    • Visit my YouTube Channel
  • Location: Albuquerque, NM
Re: Rear control arm bushings
« Reply #3 on: September 22, 2018, 02:07:16 PM »
I replaced all mine with ASR Delron bushings for the 800 RzR and custom fit nylon wear washers on all to end that issue with all the bushings. The vid is in the how-tos.
Nice! I'll take a look see at your video then. Is there a site you used and roughly about how much did you pay for the kit? Thanks for the heads up!
If you get the full kit for the RzR 800, the ones for the knuckle have to be adjusted for length...and all have to be glued-in as they don't fit tight enough...although I knurled mine most people won't be doing that..still, needed to be glued in to seal. The nylon washers I got off ebay...I think there is a link there.
2015 Z Force 800 (53") EPS -
Custom Air Intakes | Custom Exhaust Mod | SuperATV Harness | Custom Fenders | Custom Skid/Rock Sliders | 27" GBC Grim Reapers | Seizmik Mirrors |Конструктор (Rodin's) Doors | Dr Pulley Sliders | 1.5" Wheel Spacers | BENZ Silencer (as needed) | SATV Flip Windshield W\ Rear Shield | Dual Light Bars | Diamond Plate Storage | Magellan TRX7 GPS| Bandit Springs

My Videos On YouTube